AAR Approved Strapping: High Tensile Steel and Polyester Strapping With AAR Certification
JUHONG makes AAR approved strapping in high tensile steel and PET (polyester). Railroads in the United States and Canada accept it for securing loads on open top rail cars. Our AAR ID is 124, and you will find it printed on the strap. We have been manufacturing strapping products in Changzhou since 1997, and we are the only steel strapping maker in mainland China on the AAR approved list. We supply AAR strap to distributors and shippers in the rail freight industry.

What is AAR approved strapping? It is strapping that the Association of American Railroads (AAR) has tested and put on its approved list for load securement on open top rail cars. Typical applications are lumber, bricks and steel products. The approval covers one maker’s strap in specific sizes, so always check that your size is on the list.
Our AAR Approved Strapping Sizes
| Strapping | Size (inches) | Size (mm) | Joint |
|---|---|---|---|
| High tensile steel, package band | 3/4 × 0.031 | 19 × 0.79 | Sealless notch |
| High tensile steel, securement band | 1-1/4 × 0.031 | 32 × 0.79 | Sealless notch |
| Type IV PET, smooth or embossed | 5/8 × 0.035 | 16 × 0.89 | Friction weld |
| Type IV PET, smooth or embossed | 5/8 × 0.040 | 16 × 1.02 | Friction weld |
| Type IV PET, smooth or embossed | 3/4 × 0.040 | 19 × 1.02 | Friction weld |
| Type IV PET, smooth | 1-1/4 × 0.050 | 32 × 1.27 | Friction weld |
These six sizes are on the AAR approved list under ID 124, and all are made in our Changzhou plant. Need a size that is not in this table? Contact us and we will tell you what we can supply.
Why Rail Shippers Need AAR Strapping
Railroads Check It
Loads on flatcars and gondolas must follow the AAR Open Top Loading Rules. When the loading diagram calls for AAR approved strapping, the carrier expects to see it on the load.
Only Listed Sizes Count
The AAR approves one size and one joint at a time. A maker on the list can only call the listed sizes AAR approved, not its whole product range.
Package Band or Securement Band
Package bands hold a bundle together, such as a lift of lumber or a stack of pipe. Securement bands tie the load down to the rail car. Our 3/4 in steel is a package band and our 1-1/4 in steel is a securement band.
What Are the AAR Open Top Loading Rules?
The AAR Open Top Loading Rules are the rail industry’s guide to cargo securement on open top cars, such as flatcars and gondolas. Carriers in the United States and Canada use them.
For each type of cargo, a loading diagram shows how to load it and which strapping to use. Section 1 of the rules lists the approved materials. If the diagram names a material, follow it; your carrier or inspector has the final say on the requirements for each load.
The AAR publishes separate rules for closed cars and intermodal shipments. This page covers the open top rules, which most shippers use for cargo securement in rail transportation.
- Steel strappingSteel bands, approved by width and thickness
- Polyester (PET) strappingFor polyester strapping, AAR lists Type IV PET, the only plain plastic strap on the list
- Composite cord strappingPolyester cord strap, listed separately
- Tools and sealsSealless tools and metal seals have their own lists
How to Check an AAR Supplier
Four quick checks before you buy strapping for rail freight. JUHONG is on the AAR approved steel band list (current as of September 14, 2026) and the AAR approved Type IV PET list (current as of September 25, 2026).
Ask the supplier for its AAR ID. Ours is 124.
AAR approves one size at a time. Make sure the size you need is named on the supplier’s AAR certificate.
The AAR certificate lists the approved sizes and the plant location.
AAR strap is printed with the ID: our steel says “AAR 124”, our PET says “AAR124”.
AAR Steel Strapping: High Tensile Grade
Our AAR steel banding is UltiMax, our high tensile, high elongation steel strapping, in 3/4 in and 1-1/4 in widths, 0.031 in thick. The extra stretch lets it take the shocks of rail transport without snapping, so bundles stay tight. See tensile classes and break strength on our steel strapping page.
Sealless Joints, No Seals Needed
Our AAR steel is approved with sealless notch joints. The tool tensions the strap and locks the two ends by cutting notches into them, which saves seal stock on long runs. We supply manual sealless tools for strap up to 3/4 in (19 mm); see our strapping tools.
AAR PET Strapping: Type IV Polyester Strapping
Our AAR-approved PET polyester strapping is Type IV PET, the PET class on the AAR list. Four sizes are approved: 5/8 × 0.035, 5/8 × 0.040 and 3/4 × 0.040 in, smooth or embossed, and 1-1/4 × 0.050 in, smooth only, for heavier loads. The ends are joined by friction weld, which melts the two layers together, so no metal seal is needed.
Hand Grade and Machine Grade
Every AAR size comes in hand grade for battery and pneumatic power tools, and machine grade for automatic strapping machines. Rolls are wound on a 406 mm (16 in) core; heavier rolls maximize run time between changes, which helps efficiency on lines with high demand. Send us your tool or machine model and we will match the roll and surface. More grades are on our PET strapping page.
Steel or PET Strapping for Rail Freight?
PET is often used as an alternative to steel strapping on rail shipments. Both are AAR approved, so choose by the cargo.
| AAR steel strapping | AAR PET strapping | |
|---|---|---|
| Stretch and recovery | Very little stretch; best on rigid loads that do not settle | Stretches under shock with good recovery, so it stays tight on loads that shift or settle |
| Cut ends | Sharp; handle with care | No sharp edges |
| Rust | Can rust if stored wet | Does not rust |
| Heat | Fine near hot metal | Softens near high heat |
| Joint | Sealless notch | Friction weld |
Steel is the usual choice for hot or sharp-edged metal products. PET is common for lumber, bricks and building materials, and wherever cut-end safety matters. If your loading diagram names a material, follow it.
Quality Control and AAR Certification Documents
Our steel and PET are made under an ISO 9001:2015 quality system. Every two hours, inspectors take 10 coils from the line and test size and strength; a failed test stops the line. Beyond rail rules, we test to other industry standards: SGS has tested our steel to EN 13246. With a rail order we send this compliance documentation:
- The AAR certificate for steel or PET
- SGS test reports
- RoHS, REACH and SDS documents
See how we test on our quality control page, or download specifications from Downloads.
Strapping Specifications for Your Purchase Order
So the strap you receive matches the listing, state:
AAR ID 124
Steel or PET, and the size from the table above
Joint: sealless notch (steel) or friction weld (PET)
Surface: smooth or embossed PET; for steel, the finish, such as black painted and waxed
Weight per coil and core size
Quantity per pallet or per container; we ship bulk pallets and full containers
Any marking you need on the strap or label
Samples in standard sizes are free, and we confirm availability and lead time with each quotation. Our securement solutions for rail cover strap, seals and tools from one plant, so a full rail order can ship in one container.
AAR Approved Strapping FAQ
Short answers to the questions buyers ask us about AAR strapping.
What does AAR approved strapping mean?
It means the Association of American Railroads has tested a maker’s strap in a given size and joint and put it on its approved list for open top rail cars. Only the listed sizes count.
Is AAR certification the same as AAR approval?
Buyers use AAR certification, AAR-certified and AAR approved for the same thing: the strap is on the AAR list. We send our AAR certificate with your order.
Is AAR the "American Association of Railroads"?
No. The correct name is the Association of American Railroads. It publishes the Open Top Loading Rules and the approved lists.
Which JUHONG strapping sizes are AAR approved?
Steel: 3/4 × 0.031 in and 1-1/4 × 0.031 in high tensile. PET: 5/8 × 0.035 in, 5/8 × 0.040 in and 3/4 × 0.040 in (smooth or embossed) and 1-1/4 × 0.050 in (smooth). All six are under AAR ID 124.
Is all your PET strapping AAR approved?
No. Only the four Type IV PET sizes above are on the AAR list. Our other PET sizes are not.
Is JUHONG the only AAR approved steel strapping maker in China?
Yes. On the AAR approved steel band list (current as of September 14, 2026), JUHONG is the only maker in mainland China. Several Chinese companies are on the PET list. Our guide to the best steel strapping manufacturers shows which other companies hold current AAR approvals for steel bands.
Get a Quote for AAR Approved Strapping
Tell us the material, dimensions, quantity and destination, and we will send a quotation with the certificate.
- Material: high tensile steel or Type IV PET
- Dimensions and joint, from the AAR size table
- Quantity per pallet or container
- Destination port
Request a Quotation
Fields marked * are required. You can attach your coil label or specification sheet.












